lvs+keepalived+apache 部署

kyjh

系统版本：Red Hat Enterprise Linux Server release 6.3 (Santiago)
内核版本：2.6.32-279.el6.x86_64
lvs使用光盘自带的
keepalived版本：keepalived-1.2.12
apache使用光盘自带的：2.2.15
lvs的安装：
挂在光盘后
yum install ipvsadm
如果不能安装可以在包目录下找到相关的包，手动安装
IP规划：
前端：192.168.2.80-81
后端：192.168.2.82-83
部署情况：前端部署lvs和keepalived 后端部署：apache


keepalived的安装
tar -zvxf keepalived-1.2.12.tar.gz
cd keepalived-1.2.12
./configure
make
make install
cp /usr/local/etc/rc.d/init.d/keepalived /etc/rc.d/init.d/
cp /usr/local/etc/sysconfig/keepalived /etc/sysconfig/  
mkdir /etc/keepalived
cp /usr/local/etc/keepalived/keepalived.conf /etc/keepalived/
cp /usr/local/sbin/keepalived /usr/sbin/

做成系统启动服务方便管理.
添加开机启动
vi /etc/rc.local
添加
/etc/init.d/keepalived start


主的keepalived的配置请见附件

备的：
修改
state BACKUP  //类型
priority 100     //优先级，数字越大，优先级越高，主的优先级比备的高
之后启动keepalived
主备上可以看到




只有主keepalived获得浮动地址，主keepalived出现故障后备keepalived获得浮动地址
前后端节点出现故障，相关日志都会打印在/var/log/messages
前端的keepalived会根据设置的时间发包检查后端和备机的状态，如果有问题就将后端故障节点剔除，和进行主备切换

前端lvs的配置
#!/bin/bash
#description:start realserver
VIP=192.168.2.84
sh /etc/rc.d/init.d/functions
case "$1" in
start)
    echo "start LVS Of RealServer dr"
    /sbin/ifconfig lo:0 $VIP broadcast $VIP netmask 255.255.255.255 up
    /sbin/route add -host $VIP dev lo:0
    echo "1" >/proc/sys/net/ipv4/conf/lo/arp_ignore
    echo "2" >/proc/sys/net/ipv4/conf/lo/arp_announce
    echo "1" >/proc/sys/net/ipv4/conf/all/arp_ignore
    echo "2" >/proc/sys/net/ipv4/conf/all/arp_announce
    ;;
stop)
    /sbin/ifconfig lo:o down
    echo "close LVS OF realserver DR"
    echo "0" >/proc/sys/net/ipv4/conf/lo/arp_ignore
    echo "0" >/proc/sys/net/ipv4/conf/lo/arp_announce
    echo "0" >/proc/sys/net/ipv4/conf/all/arp_ignore
    echo "0" >/proc/sys/net/ipv4/conf/all/arp_announce
   ;;
*)
    echo "Usage:S0 {start | stop}"
    exit 1
esac
keepalived的作用，在这个环境中，keepalived用来配置ipvsadm，检测后端节点，故障转移之作用
keepalived有PASS和AH两种验证方式，PASS是明文,AH是加密验证，
百度云附件：主keepalived配置文件和软件.zip